CS Pressureless Soaker Hose for Rain Barrels and Water Tanks
The CS Pressureless Soaker Hose is intended for irrigation using water from a storage container. It relies on gravity rather than normal mains pressure and releases water slowly into the soil through its porous hose wall. This helps supply garden beds, hedges, raised beds and planting rows close to the roots.
- Gravity-fed operation
- Up to 25 m per straight run
- For rain barrels and IBC tanks
Irrigation Without a Pump
When the water level is sufficiently elevated, water can flow from a rain barrel or tank to the soaker hose. No additional pump is needed for this operating method.
- For vegetable beds, raised beds, hedges and greenhouses
- Suitable for gardens without a standard mains water connection
- Can be cut to the required lengths
Install Near the Roots and Plan Separate Runs
The hose can be installed above or below ground. When installed above ground, we recommend covering it with soil or bark mulch. The suitable position depends on the plants and soil conditions.
For larger projects, several separate irrigation runs can be planned. Changes in elevation and branching connections can affect water distribution.
Important Planning Information
-
Straight installation: A maximum of 25 metres of actual installed soaker hose per run.
-
Circular installation: Under suitable conditions, a total installed hose length of up to 50 metres is possible. Connect the hose at one end only and close the other end with an end cap. This is not a ring supplied from both ends.
-
Water level: A water column of 20 to 50 cm between the surface of the stored water and the hose is recommended as a guide. Available pressure decreases as the tank empties.
-
Water quality: Use clean, appropriately filtered water. Additional finer filters must not excessively restrict the low available water flow.
-
Connection: This system is intended for gravity-fed use. Do not connect it directly to an unregulated tap or pump. Any irrigation controller must be explicitly suitable for the available low pressure.
Product safety information
Manufacturer information:
CS Bewässerungssysteme GmbH
In der Aue 29
Hessen
Reichelsheim, Deutschland, 64385
info@cs-wss.com
www.cs-wss.com
Responsible person:
CS Bewässerungssysteme GmbH
In der Aue 29
Hessen
Reichelsheim, Deutschland, 64385
info@cs-wss.com
https://cs-wss.com/
| Item information |
Value |
| Shipping weight: |
9,86 kg
|
| Item weight: |
9,84 kg
|
Technical Specifications
| Product line |
CS Soaker Hose Pressureless |
| Internal diameter |
13 mm |
| Wall thickness |
2.5 mm |
| Operating principle |
Gravity-fed from a water storage container |
| Recommended water head |
approximately 20 to 50 cm |
| Maximum permitted inlet pressure |
1.5 bar (not a recommended operating pressure) |
| Maximum straight run length |
25 metres |
| Recommended maximum run length for winding or circular layouts |
15 metres |
| Maximum total installed length for circular routing |
50 metres, supplied at one end only, end cap at the other |
| Water discharge |
8 to 10 litres per metre per hour when buried, under suitable operating conditions |
| Material |
Recycled tyre granulate and recycled polyethylene |
| Colour |
Black |
| Installation |
Above or below ground, preferably close to roots |
| Country of manufacture |
Germany |
Note: Pressure depends on the height of the water surface above the hose, not on tank volume. As the tank empties, the water head decreases; pipes, filters and valves introduce additional pressure losses.
Application Notes
Water Supply and Connections
- Use the soaker hose only as a gravity-fed system with a suitable water container. It requires neither normal mains water pressure nor a pump.
- Keep the surface of the stored water approximately 20 to 50 cm above the hose. Available pressure falls as the tank empties. Place the tank on a stable, suitably elevated support.
- This set contains a 125 µm water filter. Keep it clean and only add finer filtration after checking the limited available water flow.
- Do not connect directly to an unregulated tap or pump. The maximum permitted inlet pressure of 1.5 bar is not the operating target of this gravity-fed system.
- The irrigation controller included in this set must be explicitly suitable for the actual low water head. Not every controller opens without normal mains pressure.
Installation and Irrigation Runs
- Install the hose close to the root zone where practical. Both above-ground and below-ground installation are possible. Cover exposed hose with soil or bark mulch.
- Limit straight irrigation runs to 25 metres per run.
- For circular routing, up to 50 metres of actual installed hose may be used under suitable conditions. Supply one end only and close the other end with an end cap.
- Intermediate regulating valves may be useful on sloping ground. Each connection, filter and elevation change can affect available flow.
- Check water discharge with a full and partly empty tank, including at the ends of the installed runs.
Care and Winter Storage
- Regularly inspect and clean the water container and filter to remove deposits.
- Flush the supply hose with the soaker hose disconnected at the start of the season.
- Before freezing temperatures, shut off the water and drain or store the container, filters, valves and supply lines in accordance with their respective manufacturer instructions.
Material and Odour
CS soaker hoses are manufactured using tyre granulate, among other materials. New hoses may have a slight rubber-like odour that can diminish over time.
There are no reviews yet.